＜＜BACK

1/7 R/C SQS Electric Powered Aircraft

Calmato ST EP 1400

Red

No.10062R　　 ARF Kit

 □Available : 31 Jul 2009

Ideal flight performance for the perfect introduction to stunt flying. Optimal combination of stability and maneuverability!

If you're ready to step up to a low wing stunt plane, the CALMATO ST EP 1400 is the perfect choice. This optimally balanced airplane combines excellent stability with expert-level maneuverability. The large taper ratio of the main wing and precision design fuselage delivers calm control response while the large control areas produce dynamic stunt flight capability. However, while producing the flight performance expected of a dedicated stunt flier design, the CALMATO ST EP 1400 traces its lines so smoothly though the air it stands apart from other aerobatic airplanes. In addition, the blade tip laminar flow boards included as standard deliver sensational knife edge flight and acceleration. Install the optional canalizer (No.11852-14) and the airplane sticks to its line like a tracer for unshakeable stunt flight performance. And the kit comes in ARF specifications complete with film covering. KYOSHO's unique design requires no gluing for completion of this fully equipped kit that includes brushless motor, propeller and spinner, and only requires a few additional items. For top-level electric stunt flight, the CALMATO ST EP 1400 is within easy reach of all fliers and budgets.

Taper ratio of the symmetrical main wing delivers optimal maneuverability. Balanced rear control delivers the posture indispensable to stunt plane performance.

  

Equipped with blade tip laminar flow boards that produce a high rectification effect and lower induced drag. Delivers excellent aerodynamics and knife edge performance.

  

Includes optimal combination of a 400W-class brushless motor with KV1100 and a D11 x P7 propeller to produce powerful thrust.

ABS wheel pants not only look stylish but also have a rectification effect on the tire area. The open structure is also easy to maintain and stays clean.

  

Almost fully-assembled kit requires no gluing. The user-friendly design allows the main wing to be attached by hand with wing bolts.

  

Pre-covered in layers of monochrome film for an expertly finished color scheme. Even the canopy framework is pre-painted. Only a short time is needed for completion.
  • No gluing is required to complete assembly. Color scheme complete with film covering.
  • Optimum combination of stability and maneuverability provides the ideal introduction to low-wing stunt flying.
  • Includes 400W-output KV1100 brushless motor and propeller.
  • Join the main wing halves by inserting pins and fixing with tape. Dowels are pre-glued.
  • Vertical fin and servo bed are pre-installed and linkages are also easy to setup.
  • Balsa-rib fuselage and main wing produce the lightweight ideal for stunning stunt performance.
  • Pre-installed aileron and aileron horns. Compatible with standard 4-channel, 3-servo, 1-amp R/C system.
  • Features rudder-connected tailwheel.
  • Equipped with pre-installed flexible pipe for the rudder and elevator linkage rods.
  • Includes propeller, spinner, linkage parts and foam tires.
  • Add the optional canalizer (No.11852-14) for even greater stunt capability.

＜ Required for operation ＞

  • R/C System / 4-channel, 3-servo for airplanes
  • 45A control amp for brushless motor
  • 11.1V-3,200-3,700mAh lithium polymer (No.ORI 60033 SLPB 3,200mAh lithium polymer battery 11.1V-300 recommended)
  • Battery charger
Technical Data
Length
 1,173mm
Width
 1,300mm
Weight
 1,700g (approx.)
Wing Area
 28.9dm2
Wing Load
 58.8g/dm2 (approx.)
Wing Type
 Original Symmetrical

This R/C model is not a toy!
Correct assembly and maintenance and choice of appropriate flight location is required for the safe operation of this model. Failure to use responsibly and perform required safety checks can cause fatal accidents. Beginner flyers should never fly solo.

□Last updated:09 Apr 2009

PAGE TOP